1/16 DIN Dual Channel Process Meter

  • Model: SYL-2813AC

Ask a Question

Starting at: $74.95

Please Choose:



Add to Cart:

Note: For 12V / 24V DC version dual-channel meter, please check SYL-2813 (Automobile Multimeter, Dual Channel)

Red/Red Green/Green White/White

This 1/16 DIN dual channel process meter can measure and display two parameters at the same time. It can measure temperature (RTD, thermocouple, etc), pressure and other important parameters such as DC voltage or current. Two programmable alarms will turn on the LED in the front panel to get the user's attention if the temperature/pressure is above the setting point. It will also close a relay output port that can be used to turn on a buzzer or a contactor. Each channel contains one relay. The meter stores the peak temperature/pressure with time stamps that can be checked later. It can also operate in the peak holding mode so that only the maximum value is displayed. When same type of sensors are used for both channel input, the difference between the two channel can also be displayed. It can also activate the relay at a preset value. The brightness level of the LED display is adjustable. It can also be dimmed directly from the key pad. 

One of the popular applications of this meter is to measure and display two liquid tight RTD sensors simultaneously. For PT100 RTD measurement, the meter can display from -199 °C to 250 °C (or -199 °F to 500 °F) with 0.1 degree C or F resolution when used with our RTD sensor.

For thermocouple measurement, the meter will work with most of thermocouple sensors on the market, grounded or ungrounded (please check spec below). It can display the temperature in either Celsius or Fahrenheit. 

For pressure sensor measurement, the meter will work with all of the pressure sensors we offered  It can display the pressure in either Bar, PSI, or user defined units with high resolution.  The meter can work with either older resistive pressure sensors or more modern pressure transducers with linear voltage output. The meter offers a regulated 5V DC output for the power supply of the pressure transducer.

The gauge is 48 x 48 mm.  It is 85 mm in depth. For the housing of this gauge, please check our CBox16-B

Note: if you need a thermometer to read two PT100 RTD sensors at same time, please also check SYL-2802B

Specifications:

Input type Temperature Sensor, K, E, S, R, J, T, B, WRe3-WRe25, Pt100, Cu50
Pressure transducer, 0-375ohm, 0-5V, 0-75mV
Other transducer: 0-30 mV, 1-5V, 0-10V, 0-10mA, 0-20mA, 4-20mA
Display Two lines, Four digits. °F or °C, Bar, PSI, or user defined
Display resolution Thermocouple: 1°C, 1°F; RTD/CU50: 0.1°C, 0.1°F
Display brightness control 12 V illumination control signal, or key pad
Accuracy ±0.2% or ±1 unit of full input range
Control mode On-Off
Control output Relay contact (dry relay output): 3A at 240VAC
Alarm Relay (3A rating) high/low alarm
Recording function Maximum, Max time,
Recording time 100 hrs with 1 min, or 9999 second with 1 s resolution.
Power consumption 2 Watt
Power supply voltage rating 85~264VAC/50~60Hz
Panel cutout dimension 45 x 45 mm
Dimension 48 x 48 x 85mm (1/16 DIN)

Click here to download instruction manual
Click here to download Voltage Measurement Application Guide.
Click here to download Current Measurement Application Guide.

Click here for RTD temperature sensor application guide.
Click here for Thermocouple (EGT) temperature sensor application guide.
Click here for engine fuel/oil pressure sensor installation guide.
Click here for resistive pressure sensor installation guide.


This product was added to our catalog on Monday 28 March, 2016.

Copyright © 2024 auberins.com.